152d www.vishay.com vishay sprague revision: 09-mar-12 1 document number: 40016 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 solid-electrolyte t antalex ? capacitors, extended capacitance values, hermetically-sealed features ? axial through-hole terminatons: tin/lead (snpb), 100 % tin (rohs compliant) ? high capacitance and small size ? exceptional operating stability ? hermetically-sealed, cylindrical, metal-case ? low leakage current and low dissipation factor ? the military equivalent to the 152d is the csr23 which is qualified to mil-c-39003/03 ? provide proven reliability in a wide variety of high performance military, industri al and commercial markets ? material categorization: for definitions please see www.vishay.com/doc?99912 note * lead (pb)-containing terminations are not rohs-compliant. exemptions may apply. performance characteristics operating temperature: - 55 c to + 85 c (to + 125 c with voltage derating) capacitance tolerance: at 120 hz, + 25 c 20 % and 10 % standard. 5 % available as special dissipation factor: at 120 hz, + 25 c dissipation factor, as determined from the expression 2 ? frc, shall not exceed the values listed in the standard ratings table dc leakage current (dcl max.): at + 25 c: leakage current shall not exceed the values listed in the standard ratings table at + 85 c: leakage current shall not exceed 10 times the values listed in the standard ratings table at + 125 c: leakage shall not exceed 12 times the values listed in the standard ratings table life test: capacitors shall with stand rated dc voltage applied at + 85 c for 2000 h or derated dc voltage applied at + 125 c for 1000 h following the life test: 1. dcl shall not exceed 125 % of the initial requirement. in no case need the leakage current be less than 2 a 2. dissipation factor shall meet the initial requirement 3. change in capacitance shall not exceed 5 % note (1) when a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body ordering information 152d 106 x0 006 a 2 t e3 model capacitance capacitance tolerance dc voltage rating at 85 c case code style number packaging rohs compliant this is expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros to follow. x0 = 20 % x9 = 10 % x5 = 5 % * * special order this is expressed in volts. to complete the three-digit block, zeros precede the voltage rating. see ratings and case codes table 2 = insulated sleeve t = tape and reel e3 = 100 % tin termination (rohs compliant) blank = snpb termination dimensions in inches [millimeters] case code dl j (maximum) lead size with insulating sleeve (1) awg no. nominal diameter a 0.135 0.016 [3.43 0.41] 0.286 0.031 [7.26 0.79] 0.422 [10.72] 24 0.020 [0.51] b 0.185 0.016 [4.70 0.41] 0.474 0.031 [12.04 0.79] 0.610 [15.49] 24 0.020 [0.51] r 0.289 0.016 [7.34 0.41] 0.686 0.031 [17.42 0.79] 0.822 [20.88] 22 0.025 [0.64] s 0.351 0.016 [8.92 0.41] 0.786 0.031 [19.96 0.79] 0.922 [23.42] 22 0.025 [0.64] d dia. - + 0.125 [3.18] max. solid tinned nickel leads l j max. 1.500 0.250 [38.10 6.35] 1.500 0.250 [38.10 6.35] 0.047 [1.19] max. positive lead
152d www.vishay.com vishay sprague revision: 09-mar-12 2 document number: 40016 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 standard ratings capacitance (f) case code part number max. dcl at + 25 c (a) max. df at + 25 c 120 hz (%) 6 v dc at + 85 c, surge = 8 v; 4 v dc at + 125 c, surge = 5 v 10 a 152d106(1)006a2 1.0 6 12 a 152d126(1)006a2 1.0 6 15 a 152d156(1)006a2 1.0 6 68 b 152d686(1)006b2 3.0 6 82 b 152d826(1)006b2 3.0 6 100 b 152d107(1)006b2 6.0 6 330 r 152d337(1)006r2 10.0 8 390 r 152d397(1)006r2 10.0 8 470 r 152d477(1)006r2 10.0 8 560 s 152d567(1)006s2 20.0 10 680 s 152d687(1)006s2 20.0 10 820 s 152d827(1)006s2 20.0 10 1000 s 152d108(1)006s2 20.0 10 10 v dc at + 85 c, surge = 13 v; 7 v dc at + 125 c, surge = 9 v 5.6 a 152d565(1)010a2 1.0 4 6.8 a 152d685(1)010a2 1.0 6 8.2 a 152d825(1)010a2 1.2 6 10 a 152d106(1)010a2 1.2 6 47 b 152d476(1)010b2 4.0 6 56 b 152d566(1)010b2 5.0 6 68 b 152d686(1)010b2 6.0 6 82 b 152d826(1)010b2 7.0 6 150 r 152d157(1)010r2 8.0 8 180 r 152d187(1)010r2 8.0 8 220 r 152d227(1)010r2 12.0 8 270 r 152d277(1)010r2 13.0 8 330 s 152d337(1)010s2 16.0 8 390 s 152d397(1)010s2 16.0 10 470 s 152d477(1)010s2 16.0 10 560 s 152d567(1)010s2 20.0 10 15 v dc at + 85 c, surge = 20 v; 10 v dc at + 125 c, surge = 12 v 3.9 a 152d395(1)015a2 1.0 4 4.7 a 152d475(1)015a2 1.0 4 5.6 a 152d565(1)015a2 1.3 4 6.8 a 152d685(1)015a2 1.3 6 27 b 152d276(1)015b2 3.0 6 33 b 152d336(1)015b2 5.0 6 39 b 152d396(1)015b2 5.0 6 82 r 152d826(1)015r2 8.0 6 100 r 152d107(1)015r2 10.0 8 120 r 152d127(1)015r2 10.0 8 150 r 152d157(1)015r2 15.0 8 180 r 152d187(1)015r2 15.0 8 220 s 152d227(1)015s2 20.0 8 270 s 152d277(1)015s2 20.0 8 330 s 152d337(1)015s2 20.0 8 note ? part number definitions: (1) for 10 % tolerance specify x9; for 20 % sp ecify x0; for 5 % x5 (special order)
152d www.vishay.com vishay sprague revision: 09-mar-12 3 document number: 40016 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 20 v dc at + 85 c, surge = 26 v; 13 v dc at + 125 c, surge = 16 v 2.7 a 152d275(1)020a2 0.8 4 3.3 a 152d335(1)020a2 1.0 4 3.9 a 152d395(1)020a2 1.2 4 4.7 a 152d475(1)020a2 1.2 4 18 b 152d186(1)020b2 3.0 4 22 b 152d226(1)020b2 3.0 4 27 b 152d276(1)020b2 4.0 4 56 r 152d566(1)020r2 7.0 6 68 r 152d686(1)020r2 8.0 6 82 r 152d826(1)020r2 10.0 6 100 r 152d107(1)020r2 12.0 6 120 r 152d127(1)020r2 12.0 6 150 s 152d157(1)020s2 15.0 8 180 s 152d187(1)020s2 15.0 8 220 s 152d227(1)020s2 15.0 8 30 v dc at + 85 c, surge = 39 v; 20 v dc at + 125 c, surge = 26 v 2.2 a 152d225(1)030a2 1.0 4 2.7 a 152d275(1)030a2 1.0 4 12 b 152d126(1)030b2 3.0 4 15 b 152d156(1)030b2 3.0 4 18 b 152d186(1)030b2 3.0 4 56 r 152d566(1)030r2 7.0 6 68 r 152d686(1)030r2 7.0 6 82 s 152d826(1)030s2 10.0 8 100 s 152d107(1)030s2 10.0 8 35 v dc at + 85 c, surge = 46 v; 23 v dc at + 125 c, surge = 28 v 1.2 a 152d125(1)035a2 0.6 4 1.5 a 152d155(1)035a2 0.8 4 1.8 a 152d185(1)035a2 1.0 4 8.2 b 152d825(1)035b2 3.0 4 10 b 152d106(1)035b2 3.0 4 27 r 152d276(1)035r2 7.0 6 33 r 152d336(1)035r2 8.0 6 39 r 152d396(1)035r2 10.0 6 47 r 152d476(1)035r2 10.0 6 56 s 152d566(1)035s2 12.0 6 68 s 152d686(1)035s2 12.0 6 82 s 152d826(1)035s2 30.0 8 100 s 152d107(1)035s2 30.0 8 50 v dc at + 85 c, surge = 65 v; 33 v dc at + 125 c, surge = 40 v 1.2 a 152d125(1)050a2 0.6 4 1.5 a 152d155(1)050a2 0.8 4 5.6 b 152d565(1)050b2 2.5 4 6.8 b 152d685(1)050b2 2.5 4 22 r 152d226(1)050r2 7.0 6 27 r 152d276(1)050r2 8.0 6 33 s 152d336(1)050s2 10.0 6 39 s 152d396(1)050s2 10.0 6 47 s 152d476(1)050s2 10.0 6 60 v dc at + 85 c, surge = 78 v; 39 v dc at + 125 c, surge = 49 v 22 r 152d226(1)060r2 7 6 standard ratings capacitance (f) case code part number max. dcl at + 25 c (a) max. df at + 25 c 120 hz (%) note ? part number definitions: (1) for 10 % tolerance specify x9; for 20 % sp ecify x0; for 5 % x5 (special order)
152d www.vishay.com vishay sprague revision: 09-mar-12 4 document number: 40016 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 standard reel packaging information 1. component leads a. component leads shall not be bent beyond 0.047" [1.19 mm] maximum from their nominal position when measured from the leading edge of the component lead at the lead egress from the component. b. the c dimension shall be governed by the overall length of the reel packaged component. the distance between flanges shall be 0. 125" to 0.250" [3.18 mm to 6.35 mm] greater than the overall component length. 2. orientation all polarized components must be oriented to one direction. the cathode lead tape shall be a color and the anode lead tape shall be white. 3. reeling a. components on any reel sh all not represent more than two date codes when date code identification is required. b. component leads shall be positioned between pairs of 0.250" [6.35 mm] tape. c. the disposable reels have hubs and corrugated fibreboard flanges and core or equivalent. d. a minimum of 12.0" [304.8 mm] leader of tape shall be provided before the first an d after the last component on the reel. e. 50 lb or 60 lb. kraft paper must be wound between layer of components as far as necessary for component protection. width of paper to be 0.062" to 0.250" [1.57 mm to 6.35 mm] less than the c dimension of the reel. f. a row of components must be centered between tapes 0.047" [1.19 mm]. in addi tion, individu al components may deviate from center of component row 0.031" [0.79 mm]. g. staples shall not be used for splicing. not more than 4 layers of tape shall be us ed in any splice area and no tape shall be offset from another by more than 0.031" [0.79 mm] non-cumulative. ta pe splices shall overlap at least 6.0" [152.4 mm] for butt joints and at least 3.0" [76.2 mm] for lap joints an d shall not be weaker than unspliced tape. universal splicing clips may also be used. h. quantity per reel shall be controlled so that tape components and cover shall not extend beyond the smallest dimension of the fl ange (either across flats or diameter). once the quanti ty per reel for each part number has been established, future orders for that part number shall be packaged in that quantity. when order or release quantity is less than the established quantity, a standard commercial pack is to be used. i. a maximum of 0.25 % of the components per reel quantity may be missing without consecutive missing components. j. adequate protection must be provided to prevent physical damage to both reel and components during shipment and storage. 4. marking minimum reel and carton ma rking shall consist of the following: customer part number, purchase order no., quantity, package date, manufacturers name, electrical value, date code, vishay sprague part number and country of origin. standard reel packaging specifications - meets eia standard rs-296 in inches [millimeters] case code type 150d units with insulating sleeve lead size component spacing tape spacing units per reel d l awg no. nom. dia. a b a 0.135 0.016 [3.43 0.41] 0.286 0.031 [7.26 0.79] 24 0.020 [0.51] 0.200 0.015 [5.08 0.38] 2.500 0.062 [63.5 1.57] 1000 b 0.185 0.016 [4.70 0.41] 0.474 0.031 [12.04 0.79] 24 0.020 [0.51] 0.200 0.015 [5.08 0.38] 2.500 0.062 [63.5 1.57] 1000 r 0.289 0.016 [7.34 0.41] 0.686 0.031 [17.42 0.79] 22 0.025 [0.64] 0.400 0.015 [10.16 0.38] 2.875 0.062 [73.03 1.57] 500 s 0.351 0.016 [8.92 0.41] 0.786 0.031 [19.96 0.79] 22 0.025 [0.64] 0.400 0.015 [10.16 0.38] 2.875 0.062 [73.03 1.57] 500 1.126 to 3.07 [28.6 to 78.0] i. d. reel hub 13.0 [330.2] s tandard reel thru hole label (4. a) 1.374 to 3.626 [34.9 to 92.1] s ection a to a a b both s ide s (3. f) 0.031 [0.79] max. off center (1. a) 0.125 [3.18] max. 0.250 [6.35] (3. b) 0.031 [0.79] (3. f) 0.750 [19.05] 0.625 0.0062 dia. [15.88 1.575] a a ta p e s pacing component s pacing
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
